Categories

Subtotal

View cart
Add products to your shopping cart
#1132936

Image for Illustration purposes only. Actual product may vary

MRC 5209C DOUBLE ROW BALL BRGS

$51.00 Each

NEW

  • Typically ships in: 1 day
  • Weight: 1.4 lb
  • Free shipping on orders over $20

Select Quantity

Nov. 4, 2018

The design of angular contact bearings is aimed at ensuring the axial load is accepted in one direction. Now, if loaded in the opposite direction, there is a risk of truncation of the outer ring by the outer ring’s low shoulder. The effect of this is excessive stress, high temperatures, and ultimate failure.

Read More

 

Additional Description

Item Details
Manufacturer: MRC Bearing Service
Weight: 1.432 lbs.
Product Name: 5200-C, 5200-SB Light Series Bearing
Description: 45 mm ID x 85 mm OD x 1 3/16" Wide; Open; No Snap Ring; Standard Capacity; Double Row Ball Bearing
Specifications
Inch/MetricMetric BoreBore TypeRound Bore
I.D.45 mmO.D. [Min]
O.D. [Max]O.D.85 mm
Width [Min]Width [Max]
Width30.1625 mmEnclosureOpen
Rows of BallsDoubleMaterialSteel
O.D. TypeStraightBearing TypeAngular Contact
PrecisionStandardRadial Internal Clearance SpecificationNormal Clearance
Ambient Temperature Range [Min]Ambient Temperature Range [Max]
Ball MaterialSteelCage TypeMetal
CapacityStandard CapacityContact Angle30°
Guide TypeLubrication
Outer Ring Width1 3/16 inPrecision LevelStandard (ABEC 1)
Preload LevelNoneSeal MaterialNone
Seal TypeUnsealedSeal Width
Dynamic Load Rating11000 lbfStatic Load Rating [Max]8770 lbf
Ball Dia.Bearing Design
Bore BCage MaterialSteel
Collar No.Collar O.D.
Collar WidthCorner Radius [Min]
Eccentric Collar OffsetFillet Radius1 mm
Flange O.D. [Max]Flange O.D.
Flange Width [Max]Flange Width
Flush GroundHousing Shoulder Diameter [Min]
Housing Shoulder Diameter [Max]Housing Shoulder Diameter
Industry Standard Part #Inner Ring O.D.
Inner Ring OffsetInner Ring Width1 3/16 in
Internal DesignLimiting Speed
Limiting Speed - Grease5000 rpmLimiting Speed - Oil6700 rpm
Limiting Speed - Sealed5000 rpmLocking DeviceNo Locking Device
Lube Hole CenterLubricantOil Preservative
Misalignment RangeNo. in SetSingle Bearing
No. of BallsO.D. (B)
Outer RingOuter Ring Inner Diameter
Outer Ring SizePeak Running Torque (mg-mm)
Peak Starting Torque (mg-mm)Pre Lubricant
Preload AmountRadial Internal ClearanceNormal
Radial Load Rating [Max]Radial Rigidity (lbf/µm)
Reference SpeedSeal O.D.
Seal Protection WidthSeating Washer
SeriesSet Screw Offset
Set Screw SizeShaft Shoulder Diameter [Min]
Shaft ToleranceSnap RingNo Snap Ring
Snap Ring O.D.Snap Ring Offset
Snap Ring ThicknessSpecial Features
StampingStatic Thrust Load Rating [Max]
Temperature Range [Min]Temperature Range [Max]450 °F
Use With  
Product Information
Applications
  • Recommended for applications where single-row bearings are inadequate, but radial loads are not so great as to suggest a filling-notch bearing
  • Bearings will take heavy radial loads and axial loads equally in either direction
  • Features
  • Double-row ball bearings have contact angles that converge outside the bearing, thereby increasing resistance to misalignment
  • No filling notches
  • Both the inner and outer rings have closure grooves
  • One-piece, heat-treated steel for maximum retention; snapped into place after the full quota of balls has been introduced between the inner and outer ring
  • Compliances
  • Fully meets the requirements of American Petroleum Institute Specification 610
  • Specifications:

    Cage Metal
    I.D. 1.772
    Locking None
    O.D. 3.346
    Bearing Type Angular Contact
    Enclosure Open

    Return policy

    Item must be unused.

    Item must be in it's original package.

    Product's availability

    State of California Proposition 65 Product Warning