Call (888)-671-2883
FREE SHIPPING
 on most items
Text message to Live Chat! (210) 878 - 2676

LoveJoy 68514413896 UFH125R CPLG 3/4 3/16X3/32K

BRAND: LoveJoy | MODEL: 68514413896 | CONDITION: NEW | SKU: 1796259
LoveJoy 68514413896 UFH125R CPLG 3/4 3/16X3/32K

Image for Illustration purposes only,
Actual product may vary
$349.14
FREE SHIPPING
Typically In Stock: confirm availability
Returnable: see conditions
Shipping from?: see locations Ships in 1 day
Weight: 3.00 lbs UOM: EA
100% SAFE SHOPPING
PAYMENT METHOD
 
 

Additional Description

Documents

Description

UFH Type - Flange-to-Shaft
    A flange-to-shaft configuration, this couples flange mounted equipment to a shaft with all the benefits of Uniflex versatility. The stock flange plate is the same as used on the UF Type.The one-piece UFH Type coupling is similar to the U Type, except that one hub is replaced by a flange plate. Stock flange sizes are shown in the Dimensional Data table below but other sizes can be made to order. As with the other Uniflex styles, this coupling compensates for high degrees of angular and parallel misalignment with very little backlash or windup and is reliable in harsh or severe environments.Regular and short versions are available for each size to accommodate different overall length requirements. For increased versatility, the hub can be modified with a tapered, spline, hex or square bore. The standard hub is furnished with either a pre-drilled pin hole or with a keyway and set screw. Specify when ordering.
    Note: The UFH Type coupling does not come with assembly hardware. Assembly hardware must be purchased separately.
Specifications
Description UFH125R CPLG 3/4 3/16X3/32K
Hub StyleRegular
TypeFlange-to-Shaft
MaterialSteel
Weight3.00 lb
ColorGray/Metallic
Bore TypeFinished Bore
# of Mounting Screws Required3
Dimensional Data
Bore Size 3/4 in
Hub SizeUFH125R
Set Screw Thread Size (Dimension T)3/8-16
Keyway Size (W x D)3/16 x 3/32 in
Dimension HD2.170 in55.12 mm
Overall Length3.75 in95.25 mm
Pin Location (Dimension SL)0.62 in
Length thru Bore1.280 in32.51 mm
Min. Bore (Dimensions ID1/ID2)0.625 in15.88 mm
Max. Bore (Dimensions ID1/ID2)1.25 in32.00 mm
Dimension BC3.120 in79.25 mm
Dimension D3.560 in90.42 mm
Flange Diameter (Dimension FD)3.680 in93.47 mm
Dimension FL0.500 in12.70 mm
Mounting Screw Thread Size5/16-18
Cubic inches50.78400 in³
Performance Data
Operating Temperature Range-40 to 250 ºF
Max. Torque755 in·lb
Max. Speed6000 rpm
Max. Recommended End Play0.040 in1.02 mm
Max. Parallel Offset0.044 in1.12 mm
Wind-Up Angle at Nominal Torque1.85 º
Wind-Up Angle at Max. Torque4.5 º
Rated HP at 100 rpm1.21 hp
# of Set Screws Required1
Coupling Design
    The Uniflex Coupling is an all steel, single piece coupling that solves a variety of application concerns including: high misalignment, space limitations, high temperature, and exceptionally low backlash/windup. The unique flexing center of the Uniflex consists of three opposingly wound square wire springs for forward or reverse operation. Two steel hubs are then brazed to the steel spring pack to create a durable one-piece flexible coupling.
Notes
  • Total backlash is approximately 1/3 of windup at maximum torque – consult Lovejoy Engineering for more information.
  • OAL & Dimension FL Tolerance + .12 inch.
  • Mounting screws not supplied.