Call (888)-671-2883
 on most items
Text message to Live Chat! (201) 898 - 2676

UFH137S CPLG 7/8 3/16X3/32KW

BRAND: LoveJoy | MODEL: 68514413910 | CONDITION: NEW | SKU: 1796263
UFH137S CPLG 7/8 3/16X3/32KW

Image for Illustration purposes only,
Actual product may vary
Typically In Stock: confirm availability
Returnable: see conditions
Shipping from?: see locations Typically ships in 1 day
Weight: 4.50 lbs UOM: EA

Additional Description



UFH Type - Flange-to-Shaft
    A flange-to-shaft configuration, this couples flange mounted equipment to a shaft with all the benefits of Uniflex versatility. The stock flange plate is the same as used on the UF Type.The one-piece UFH Type coupling is similar to the U Type, except that one hub is replaced by a flange plate. Stock flange sizes are shown in the Dimensional Data table below but other sizes can be made to order. As with the other Uniflex styles, this coupling compensates for high degrees of angular and parallel misalignment with very little backlash or windup and is reliable in harsh or severe environments.Regular and short versions are available for each size to accommodate different overall length requirements. For increased versatility, the hub can be modified with a tapered, spline, hex or square bore. The standard hub is furnished with either a pre-drilled pin hole or with a keyway and set screw. Specify when ordering.
    Note: The UFH Type coupling does not come with assembly hardware. Assembly hardware must be purchased separately.
Description UFH137S CPLG 7/8 3/16X3/32KW
Hub StyleShort
Weight4.50 lb
Bore TypeFinished Bore
# of Mounting Screws Required3
Dimensional Data
Bore Size 7/8 in
Hub SizeUFH137S
Set Screw Thread Size (Dimension T)3/8-16
Keyway Size (W x D)3/16 x 3/32 in
Dimension HD2.540 in64.52 mm
Overall Length3.460 in87.88 mm
Pin Location (Dimension SL)0.69 in
Length thru Bore1.020 in25.91 mm
Min. Bore (Dimensions ID1/ID2)0.625 in15.88 mm
Max. Bore (Dimensions ID1/ID2)1.375 in35.00 mm
Dimension BC3.750 in95.25 mm
Dimension D4.250 in107.95 mm
Flange Diameter (Dimension FD)4.380 in111.25 mm
Dimension FL0.500 in12.70 mm
Mounting Screw Thread Size3/8-16
Cubic inches58.73142 in³
Performance Data
Operating Temperature Range-40 to 250 ºF
Max. Torque1260 in·lb
Max. Speed6000 rpm
Max. Recommended End Play0.020 in0.51 mm
Max. Parallel Offset0.350 in0.89 mm
Wind-Up Angle at Nominal Torque1.35 º
Wind-Up Angle at Max. Torque3.00 º
Rated HP at 100 rpm2.02 hp
# of Set Screws Required1
Coupling Design
    The Uniflex Coupling is an all steel, single piece coupling that solves a variety of application concerns including: high misalignment, space limitations, high temperature, and exceptionally low backlash/windup. The unique flexing center of the Uniflex consists of three opposingly wound square wire springs for forward or reverse operation. Two steel hubs are then brazed to the steel spring pack to create a durable one-piece flexible coupling.
  • Total backlash is approximately 1/3 of windup at maximum torque – consult Lovejoy Engineering for more information.
  • OAL & Dimension FL Tolerance + .12 inch.
  • Mounting screws not supplied.