We never sell your data to third parties
Image for Illustration purposes only. Actual product may vary
Dodge 035917 P4B316-USAF-080MTT four-bolt pillow block mounted spherical roller bearing with 80mm bore, split cast iron housing, grease lubrication, and direct shaft mount. Non-expansion fixed design, sensor-ready, for heavy-duty industrial applications.
MODEL 035917
Contact supplier for technical support on: +1-864-284-5700
Call for Pricing - 888-671-2883
Typically Ships in: 1 day
Returnable: See conditions
Base to center height
4.2500 in, 107.95 mm
Bearing component
Mounted Bearing
Bearing type
Spherical roller, spherical roller
Bolt Diameter
0.6250 in
Bolt to bolt max
12.5000 in, 317.5 mm
Bolt to bolt min
10.6300 in, 270.002 mm
Bolt width
2.1300 in, 54.102 mm
Bore length
6.4200 in, 163.068 mm
Expansion capability
Non-expansion (fixed)
Greasable
Yes
Housing construction
Split
Housing type
Four-bolt pillow block
Insert material
Steel
Lubrication type
Grease
Max Speed
2200 RPM
Sensor ready
Yes
Shaft attachment
Direct Mount
Shaft diameter
80.0000 mm
Static load capacity
114000 lbf, 507097.264 N
DODGE UNIFIED SAF and SDAF Pillow Blocks
Features/Benefits
- Cast iron, closed-end housings offer greater protection in high pressure washdown environments. Available from stock.
- Solid cast iron feet increase strength in both two and fourbolt styles.
- Large capacity oil sump lowers operating temperatures, undercut bearing seat allows full lateral travel of expansion bearing, prevents stabilizer ring from binding, makes installation easy
- Oil return slots are cast into the interior seal grooves to keep lubricants in. This allows oil in the seal grooves to return to the oil sump instead of leaking.
- Standard modifications for wet and harsh environments include nylon coating, epoxy paints and nickel plating, as well as stainless steel hardware.
- New drop-in TRIPLE-TECT Seal makes seal installation easier
- Exclusive oil-equalization passage simplifies maintenance. Pillow block can be drained completely from either side.
- Offset dowels with matched numbers on cap and base joint simplify correct assembly.
SKU: 115894
Excellent
We recently purchased a 30-year old hydroseeder and have no manuals or parts diagrams for it. The manufacturer is since out of business and there is very limited information on line. The most critical part we needed was a Dodge part. The original part was clearly marked with the Dodge name and part number. MRO was quickly able to identify the replacement part and we had in hand in two days. Perfect fit. Thank you MRO Supply for helping make our machine functional.
Read moreSKU: 126887
Bearings
Order arrived on time, could have been packed a little tighter as the boxes the bearings came in were tore up. All is good as i used all of them instead of leaving them set in inventory.
Read moreSKU: 127693
Re-seller discount needed
Quick delivery, but I think you should raise your prices for end users and lower your prices for resellers like myself!
Read more
Face Runout/OD is the variation of the outside surface generatrix inclination with the face. This tolerance is meant to help ensure the outer ring of the bearing is close enough to a right angle with the face of the outer ring. The figures for the face runout/OD are provided for P4 and P5 grades. Note that all points on a single circle of the outside ring bore adjacent to the face are calculated based on one revolution. However, the inner ring must remain stationary. Then, the bearing is turned over and the outer side of the ring measured. Finally, the largest measurement is taken away from the smallest to get runout/OD bore tolerance.
Read More
| Brand | Pfannenberg |
| Model | 32074155000 |
| Brand | Cle-Line |
| Model | C23517 |
| Brand | Wiegmann |
| Model | FH230V200W |
| Brand | Bando |
| Model | A32 |
| Brand | Pfannenberg |
| Model | 31120805000 |
| Brand | Hubbell Wiring |
| Model | CKTSD |
| Brand | Bando |
| Model | E210 |
SKU: 115894
Excellent
We recently purchased a 30-year old hydroseeder and have no manuals or parts diagrams for it. The manufacturer is since out of business and there is very limited information on line. The most critical part we needed was a Dodge part. The original part was clearly marked with the Dodge name and part number. MRO was quickly able to identify the replacement part and we had in hand in two days. Perfect fit. Thank you MRO Supply for helping make our machine functional.
Read moreSKU: 126887
Bearings
Order arrived on time, could have been packed a little tighter as the boxes the bearings came in were tore up. All is good as i used all of them instead of leaving them set in inventory.
Read moreSKU: 127693
Re-seller discount needed
Quick delivery, but I think you should raise your prices for end users and lower your prices for resellers like myself!
Read moreItem must be unused and undamaged, in it's orginal package. For Dodge there is typically a 10% + $30 US re-stocking fee, although it may vary from case to case. Re-packing fees may apply. Re-stocking fee applies bor both returns for credit and return for exchange.
Warranty is redeemed directly with manufacturer. If your item was damaged during usage, please let us know and we will help you get in touch with your nearest service center, they will guide you about the steps to follow to redeem the manufacturer's warranty.
For further information on our returns/warranty policy, please visit:
https://www.mrosupply.com/page/returnwarranty-policy/