We never sell your data to third parties
Image for Illustration purposes only. Actual product may vary
Dodge 039164 CP4B544-USAF-800TT four-bolt pillow block mounted spherical roller bearing with 8" bore, tapered adapter shaft attachment, split cast iron housing, non-expansion fixed design, sensor-ready, and grease lubrication for heavy-duty industrial
MODEL 039164
Contact supplier for technical support on: +1-864-284-5700
$11,758.38 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $100
Select Quantity
Typically Ships in: 1 day
Returnable: See conditions
Base to center height
9.5000 in, 241.3 mm
Bearing component
Mounted Bearing
Bearing type
Spherical roller, spherical roller
Bolt Diameter
1.5000 in
Bolt to bolt max
27.8800 in, 708.152 mm
Bolt to bolt min
24.7500 in, 628.65 mm
Bolt width
5.2500 in, 133.35 mm
Bore length
12.1300 in, 308.102 mm
Expansion capability
Non-expansion (fixed)
Greasable
Yes
Housing construction
Split
Housing type
Four-bolt pillow block
Insert material
Steel
Lubrication type
Grease
Max Speed
950 RPM
Sensor ready
Yes
Shaft attachment
Tapered adapter
Shaft diameter
8.0000 in
Static load capacity
450000 lbf, 2001699.727 N
DODGE UNIFIED SAF and SDAF Pillow Blocks
BEARINGS
Spherical Roller Bearing - 22200, 22300, 23000, 23100 and 23200, tapered bore for adapter mount and straight bore for direct mount.
SPLIT-SPHER Bearing
Complete split replacement for an adapter mounted 22200. Compatible with UNIFIED SAF. Available in inch bores.
SHAFT SIZES
Available for shaft sizes 1-7/16” - 15-3/4” and 40 mm-140 mm in adapter mount. Additional sizes offered in direct mount. Pillow blocks are available in 200, 300, 500 and 600 series.
DIMENSIONS
UNIFIED SAF and SDAF pillow blocks match standard SAF and SDAF inch dimensions.
PLUS YOU GET BUILT-IN DESIGN ADVANCEMENTS
With DODGE UNIFIED SAF and SDAF pillow blocks, you benefit from a housing that has capabilities for harsh environments that competitive pillow blocks do not have.
VIRTUALLY EVERY FEATURE YOU EVER WANTED IN YOUR PILLOW BLOCK
- Cast-in dimples locate drill holes for lube fittings, vents, sensors and mounting modifications.
- Housing base is threaded to accept four Grade 5 cap bolts for added strength. Cap bolts match base bolts for one-wrench installation.
- Standard housings have two oversized drains adaptable to circulating oil systems.
- Pry slots allow easy separation of the pillow block.
SKU: 118299
Prompt & great service
As usual MRO Supply team are quick in shipping the ordered parts correctly without any delay.. Will shop online again confidently knowing they offer very good and prompt service!
Read moreSKU: 126926
Oem parts
I was repairing a piece of equipment and wanted the same bearings that were removed. MRO Supply had the OEM bearings at a reduced cost. Shipped and received in a timely manner.
Read more
Face Runout/OD is the variation of the outside surface generatrix inclination with the face. This tolerance is meant to help ensure the outer ring of the bearing is close enough to a right angle with the face of the outer ring. The figures for the face runout/OD are provided for P4 and P5 grades. Note that all points on a single circle of the outside ring bore adjacent to the face are calculated based on one revolution. However, the inner ring must remain stationary. Then, the bearing is turned over and the outer side of the ring measured. Finally, the largest measurement is taken away from the smallest to get runout/OD bore tolerance.
Read More
| Brand | Ringfeder |
| Model | 4061-175 |
| Brand | Timken |
| Model | SME20K |
| Brand | Ringfeder |
| Model | 4091-165SR |
| Brand | Saginaw Control |
| Model | SCE-3PBSS |
| Brand | Isostatic |
| Model | EP101408 |
SKU: 118299
Prompt & great service
As usual MRO Supply team are quick in shipping the ordered parts correctly without any delay.. Will shop online again confidently knowing they offer very good and prompt service!
Read moreSKU: 126926
Oem parts
I was repairing a piece of equipment and wanted the same bearings that were removed. MRO Supply had the OEM bearings at a reduced cost. Shipped and received in a timely manner.
Read moreItem must be unused and undamaged, in it's orginal package. For Dodge there is typically a 10% + $30 US re-stocking fee, although it may vary from case to case. Re-packing fees may apply. Re-stocking fee applies bor both returns for credit and return for exchange.
Warranty is redeemed directly with manufacturer. If your item was damaged during usage, please let us know and we will help you get in touch with your nearest service center, they will guide you about the steps to follow to redeem the manufacturer's warranty.
For further information on our returns/warranty policy, please visit:
https://www.mrosupply.com/page/returnwarranty-policy/