We never sell your data to third parties
Image for Illustration purposes only. Actual product may vary
Timken LSM35BRHFRSS is a split cylindrical roller bearing housed unit with a 4-bolt flange mount. This assembly features a split housing design for simplified installation and maintenance on industrial shafts. The cylindrical roller bearing insert provides high radial load capacity for demanding applications such as gear reducers, heavy conveyors, and industrial machinery where rigid shaft support is required.
MODEL LSM35BRHFRSS
$1,464.72 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $100
Select Quantity
Typically Ships in: 1 day
Returnable: Yes
164 mm Dimension V
0.1 in
204 mm Dimension R
6.5 in
3 mm Dynamic load rating
14613 lbf 65000 N Housing:LSM35HR Max Speed:5400 rpm Note:KPS, RSS, ATL and HTPS seals. . Seal type:Viton Single Lip Series type:Light Series Shaft Size:35 mm Support type:Round Flange
Axial Load Rating
719.38 lbf
Bearing - Housing - Seal
LSM35BRHRSS
Bearing - Housing - Seal UPC
013992091291
Bearing Number
LSM35BR
Bearing Type
Split Cylindrical Retained Type
Bearing UPC
013992029621
Bolt Size
4 x M12
Ca - Axial Load Rating
719.38 lbf 3200 N
Cor - Static Load Rating
15287 lbf 68000 N
Cr - Dynamic Load Rating
14613 lbf 65000 N
Dimension H
2 in 51 mm
Dimension L
3.7 in 93 mm
Dimension N
4.687 in 119.06 mm
Dimension P
0.5 in 13 mm
Dimension R
6.5 in 164 mm
Dimension T
8 in 204 mm
Dimension V
0.1 in 3 mm
Dynamic Load Rating
14613 lbf
Housing
LSM35HR
Maximum Speed
5400 rpm
Note
Timken offers a wide range of sealing options including: KPS, RSS, ATL and HTPS seals. .
Seal Type
Viton Single Lip
Series Type
Light Series
Shaft Size
35 mm
Static Load Rating
15287 lbf
Support Type
Round Flange
When faced with flat horizontal or vertical faces, flange units offer a simple mounting solution. As with pillow block supports, flange units are produced with spherical location to accommodate standard bearing housings and provide easy initial alignment of shaft and equipment.
To facilitate positive location of the flange to the surface, the rear face is recessed (dimensions N & V). This allows for a spigot (Tolerance f8) to be located into the flange.
Bearing inspection is simply a matter of removing the top half of the flange and housing. Bearing replacement may also be achieved in the same manner if required.
When integrating flange units into new applications, it should be noted that a maximum radial load equivalent to 0.26Cor is permissible. A maximum axial load of 0.25Ca must also be taken into account for applications with thrust loading. Units for vertically oriented shafts may also need special consideration given to sealing arrangements.
As always, Timken will be happy to advise on any application issues.
SKU: 5066946
Best company to buy from
I always buy from MRO is a very reliable company to work with
Read moreHow do I choose the right type of bearing for my application?
Start with the load and how it’s applied. You need to know if you’re dealing with radial loads, axial loads, or a mix of both. Then look at speed, operating environment, and space constraints. For example, ball bearings are great for high speed and lighter loads, while roller bearings handle heavier loads but usually at lower speeds. If there’s contamination, moisture, or heat involved, you may need sealed bearings or specific materials. In most cases, the right choice comes down to matching load type, speed, and environment to the bearing design.
| Brand | MROSupply Fasteners |
| Model | FSTPCK-492048 |
| Brand | Deublin |
| Model | 527-130-054 |
| Brand | Tingley |
| Model | J31207-2XL |
| Brand | Maxi-Lift |
| Model | TTHP07X5 P O |
SKU: 5066946
Best company to buy from
I always buy from MRO is a very reliable company to work with
Read more