We never sell your data to third parties
SKF F2BC 103-TPZM is a 1-3/16 inch shaft 2-bolt flange bearing unit with a corrosion-resistant cast-iron housing. The insert bearing is pre-lubricated and features set-screw locking for secure shaft mounting. Designed for light to moderate radial loads in food processing, washdown, and outdoor applications.
MODEL F2BC 103-TPZM
$89.69 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $100
Select Quantity
Typically Ships in: 1 day
Returnable: See conditions
Application
For food and beverage applications
Attachment Bolt Diameter
9.525 mm
Basic Dynamic Load Rating
19.5 kN
Basic Static Load Rating
11.2 kN
Bearing Material
Bearing steel
Bearing Sealing
Seal and flinger on both sides
Bore Type
Cylindrical
Centre Distance Between Bolt Holes
117 mm
Coating
Zinc-coated bearing
Fastening Bolt Hole Type
Plain
Flanged Housing Type
Oval
Grease Fitting
Without
Hexagonal Key Size for Set Screw
3.175 mm
Housing
Composite for the SKF Food Line
Housing Overall Width
33 mm
Housing Type
Flanged
Inner Ring Retaining Feature
Set screws
Limiting Speed
3800 r/min
Lubricant
Grease
Number of Bolt Holes for Fasteners
2
Pack Height
148 mm
Pack Length
88 mm
Pack Width
54 mm
Relubrication Hole
Without
Rubber Seating Ring
Without
Sealing Type
Contact, gutter
Set Screw
1/4-28 UNF
Set Screw Tightening Torque
4 N·m
Shaft Diameter
30.1625 mm
Total Bearing Width
38.1 mm
Unit Sealing
Optional end cover
Oval flanged ball bearing unit with set screw locking and extended inner ring, composite housing, SKF Food Line
These oval flanged ball bearing units are designed especially for the food and beverage industries. They are chemical resistant, lightweight and strong. The unit consists of an insert bearing, with an extended inner ring and set screw locking, and is suitable for applications where the direction of rotation is constant or alternating. The bearing is mounted in a composite housing, which can be bolted to a machine wall or frame. Ball bearing units can accommodate moderate initial misalignment, but normally do not permit axial displacement.
- Chemical resistant
- Lubricated for life with a non-toxic food grade grease
- Lightweight
- Strong
How do I choose the right type of bearing for my application?
Start with the load and how it’s applied. You need to know if you’re dealing with radial loads, axial loads, or a mix of both. Then look at speed, operating environment, and space constraints. For example, ball bearings are great for high speed and lighter loads, while roller bearings handle heavier loads but usually at lower speeds. If there’s contamination, moisture, or heat involved, you may need sealed bearings or specific materials. In most cases, the right choice comes down to matching load type, speed, and environment to the bearing design.
What is the difference between deep groove and angular contact ball bearings?
Deep groove ball bearings are the most common type. They’re designed to handle mainly radial loads, but they can also take some axial load in both directions. They’re simple, versatile, and used in everything from motors to conveyors. Angular contact ball bearings are built for combined loads, especially where there’s significant axial force in one direction. They’re often used in pairs and are common in higher precision or higher load applications like pumps and gearboxes. If your load is mostly radial, go deep groove. If axial load matters more, angular contact is usually the better choice.
| Brand | Teco-Westinghouse |
| Model | E7006 |
| Brand | PEER Bearing |
| Model | FHLF202-10G |
| Brand | PEER Bearing |
| Model | FHLF205-14G |
| Brand | Brook Crompton |
| Model | AC4M001-EC |
Disclaimer: The return policy information shown below is merely an excerpt from SKF's General Conditions of Sale.
RETURN OF GOODS FOR CREDIT
Goods will not be accepted for return without prior written approval from SKF. The return freight must be prepaid by the Buyer. Unless return of Goods is due to Supplier error, Goods returned will be subject to a credit service fee of $25.00 or 15% of the credit value, whichever is greater. An additional service fee may apply is further inspection is required at the discretion of SKF