We never sell your data to third parties
Dodge 117389 SDS-30mm Quick Disconnect (QD) bushing for 30mm metric shafts, 8x3.3mm keyway. Sintered steel construction provides reliable power transmission component mounting with easy installation and removal. Type SDS QD bushing for industrial sheaves, sprockets, and pulleys.
MODEL 117389
Contact supplier for technical support on: +1-864-284-5700
$39.80 Each
Prices are subject to change
ADD $60.20 MORE FOR FREE SHIPPING
Select Quantity
Typically Ships in: 1 day
Returnable: See conditions
Bore diameter actual
30.0000 mm, 1.181 in
Bore length
1.3100 in, 33.274 mm
Bushing size
SDS
Bushing type
QD
I.D.
30 mm
Installation torque
108 in/lb, 108.0 in/lb
Integral key
No
Keyway
8 x 3.3 mm
Keyway size
8 X 7
Material
Sintered steel
Number of bolts
3
Rated Torque
5000.0000 lbf, 22241.108 N
Shaft attachment
Finished bore
QD Bushing - Metric Bore/Metric Hardware
- DODGE QD-style bushings stocked in popular finish bore sizes and minimum plain bore, for custom reboring
- DODGE Metric QD bushings supplied with metric hex-head cap screws and lock washers
- Stock reborable bushings available for custom reboring
- Reboring and sawsplit available from DODGE for nominal extra charge
- Can be used with DODGE HTD sprockets for conventional mounting only (English thread hardware required for demounting.)
NOTE: Rebore by others must be sawsplit after rebore
QD Bushings features and Benefits
- 4 Degree Taper
- Easy on/Easy off
- Manufactured precisely to industry standards
- Conventional or Reverse Mounting, Including sizes M thru W - DODGE exclusive!
- QD is a registered trademark of Emerson Electric
Conventional Mounting
- Easy On
- Place bushing in product
- Align clearance holes in product with threaded holes in bushing
- Install screws and lockwashers thru clearance holes, finger tight
- Slide assembly onto shaft, flange first
- Locate assembly on shaft for proper drive align ment
- Tighten cap screws alternately and evenly to specified torque
- Easy Off
- Remove cap screws and install in product threaded holes
- Alternately and evenly tighten screws until bush ing grip is released
- Flanged Design
Reverse Mounting
- Easy On
- Place bushing in product
- Align clearance holes in product with threaded holes in bushing
- Install screws and lockwashers thru clearance holes, finger tight
- Slide assembly onto shaft, flange outward
- Locate assembly on shaft for proper drive align ment
- Tighten cap screws alternately and evenly to specified torque
- Easy Off
- Remove cap screws and reinstall in flange threaded holes
- Alternately and evenly tighten screws until bush ing grip is released
IMPORTANT!
Do not use lubricants or anti-seize compounds on tapered bore or bushing surfaces. Complete installation instructions are available at www.dodge-pt.com.
SKU: 126926
Oem parts
I was repairing a piece of equipment and wanted the same bearings that were removed. MRO Supply had the OEM bearings at a reduced cost. Shipped and received in a timely manner.
Read moreHow does Dodge warranty evaluation work if a product fails? This product
Failed units go to Dodge's US plants for evaluation — about a week in transit plus one to two weeks of analysis, and you get the findings either way. Warranty covers workmanship and material defects; failures caused by the application (lubrication, installation) fall to the customer, but the failure analysis tells you the root cause so it doesn't repeat.
#832812
Brand
TB Woods
Model
2RBX136
#1243180
Brand
Gates Rubber
Model
LL8MGT-036
#2283145
Brand
Browning
Model
1071521
#2929282
Brand
Ringfeder
Model
4181-420
#5765621
Brand
Enerpac
Model
IPL-100
#390042
Brand
U.S.Tsubaki
Model
SDS-1C
#2839190
Brand
Hammond Power Solutions
Model
SG3A0750DB0C
SKU: 126926
Oem parts
I was repairing a piece of equipment and wanted the same bearings that were removed. MRO Supply had the OEM bearings at a reduced cost. Shipped and received in a timely manner.
Read moreItem must be unused and undamaged, in it's orginal package. For Dodge there is typically a 10% + $30 US re-stocking fee, although it may vary from case to case. Re-packing fees may apply. Re-stocking fee applies bor both returns for credit and return for exchange.
Warranty is redeemed directly with manufacturer. If your item was damaged during usage, please let us know and we will help you get in touch with your nearest service center, they will guide you about the steps to follow to redeem the manufacturer's warranty.
For further information on our returns/warranty policy, please visit:
https://www.mrosupply.com/page/returnwarranty-policy/