We never sell your data to third parties
Morse 604201 500A TL FACING (2) PB TORQUE LIMITERS-MORSE
MODEL 604201
Contact supplier for technical support on: 800-626-2120
$81.97 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $100
Select Quantity
Returnable:No
Brand
Morse
Model
604207
Brand
Morse
Model
604206
Brand
Morse
Model
100523
Brand
Morse
Model
194627
Height
0.75
Length
5.05
Product Type
Torque Overload Accessories
Series / Model
500A
Type of OSD
Morse (TM) Torque Limiter
Width
5.4
Regal Beloit Morse 500A TL FACING (2) PB
UPC: 662288495055 | UNSPSC: 40161515 | GTIN:
Clutches & Brakes > Torque Limiters & Overload Protectors > Torque Limiter Parts
Morse® Friction Facing, Unbonded, For Use With: 500A Series Plain Bore Torque Limiter, Non-Asbestos, 5 in Dia x 5/32 in THK
Features:
- Made of non-asbestos, non-lead material, providing a high coefficient of friction and long wear
Specs:
- Dimensions: 5 in Dia x 5/32 in THK
- Material: Non-Asbestos
- Suitable For Use With: 500A Series Plain Bore Torque Limiter
- Type: Unbonded
No questions match your search.
How do I read a Morse torque limiter part number like 700A-2 TL 1-1/2 FB? This product
This key covers the 250A to 700A. The first number is the size and overall diameter: 250A is 2.5 in, 350A 3.5 in, 500A 5 in and 700A 7 in. The digit after the dash is the number of disk springs, 1 or 2, so a 700A-1 slips at 85 to 420 lb-ft and a 700A-2 at 165 to 800. TL is the series, torque limiter. The end is the bore: FB is a stock finished bore with keyway and setscrew, MPB a minimum plain bore for reboring. The dash number is the spring count on the Model 150 and the 13 in and 20 in models too: 150A-4 has four, 13-8 eight.
Does a Morse torque limiter come with the bushing and sprocket? This product
No. The bushing and the center member (sprocket, sheave, gear or plate) are ordered separately, except on the Model 150, which uses no bushing. Bushing length is set by the center member: the 700A, for example, takes bushings from .520 to 1.375 in, matched to chain pitch. Morse stocks ground A plate sprockets for the 250 to 700 models: 700-AG826 fits the 700, #80 chain, 26 teeth. A sprocket package such as 700-AG826 SPKT PKG is the sprocket only, so order the bushing too. A stock 700A-2 TL ships with facings, pressure plate, springs and adjusting nut assembled on the hub.
Can I use my own sprocket or sheave in a Morse torque limiter? This product
Yes, if it is prepared to suit. The center member's faces must be flat, parallel, square with the bore and free of rust, scale and oil, with a 63 micro-inch finish where the facings rub and a 125 micro-inch finish in the bore. The bore must be counterbored to the bushing diameter for that size, for example 4.129 to 4.131 in on the 700A, and the sprocket must have at least the minimum teeth listed for its chain pitch. Stock sprockets in minimum plain bore need reboring and face grinding first. Unground center members give erratic and generally lower slip torque.
How do I set and check the slip torque on a Morse 250A to 700A torque limiter? This product
Run in first: set 70 to 80 percent of the single spring rating and slip the center member at about 60 rpm for 4 minutes. On the 250A and 350A, set the adjusting nut and lock it with the tab washer. On the 500A and 700A, back out the three cap screws, run the nut finger tight (less for lower torque), then tighten the screws alternately, half a turn at a time, until the heads bottom; back them off before readjusting. Never fully flatten the spring. To check, clamp it on a stub shaft in a vise and load a chain on the sprocket: radius in feet times pounds should run 5 to 10 percent above the slip torque needed.
Which parts wear on a Morse torque limiter, and can I use one as a shaft coupling? This product
Friction facings and bushings are the only parts that normally need replacing; disk springs are also sold separately. Facings come as a pair, such as 700A TL FACING (2), and both should be replaced together. At regular intervals inspect for oil, grease, moisture or rust on the friction surfaces, then clean and reset: rust on the center plate can greatly shorten facing life. For longest wear, mount it on the low speed shaft. Never use a torque limiter alone as a coupling. For shaft to shaft drives use a Morse torque limiter coupling (250CP, 350CP, 500CP or 700CP), which adds two sprockets, a bushing and double roller chain; the torque limiter is ordered separately.
Perfect fit
Verified · SKU 2296257Exact match with highly informed technical data to search and get the correct part. I highly recommend MRO Supply! Read more
Consistent quality
Verified · SKU 2296540Second purchase, will come again next time. Read more
Great service
Verified · SKU 2296269Absolute superb service and timely delivery. Would do business again. 🙌 Read more
Brand
IPTCI Bearing
Model
NAPL 209 26
Brand
SKF Bearing
Model
22336 CCK/W33
Brand
SKF Bearing
Model
NATR 25 PPA
Brand
INA Bearing
Model
NATR12