Add products to your shopping cart

$44.23 Each Prices subject to change


Image for Illustration purposes only. Actual product may vary

Dixon 306 2" Boss Clamp 4-Gripping Fingers Iron Bolt-MB8300 Nut-MN8






4.860 lb



Contact supplier for technical support on: 877-963-4966

$44.23 Each

Prices are subject to change


Select Quantity


Typically Ships in: 1 day

Returnable: See conditions

Still Deciding?

Add this item to your saved items and easily come back later.


MaterialZinc Plated Iron
Hose ID2" (50mm)
Hose OD From2-48/64" (69.9mm)
Hose OD To3-4/64" (77.8mm)
Torque60 ft. lbs.
Weight Lb4.8600
  • Bolts in Boss Clamps are designed to bend as they are tightened. This allows the clamp to conform to the hose outside diameter.
  • Always tighten bolts to their specified torque value.
  • Periodic re-tightening of bolts is required due to "cold flow" phenomenon present in all rubber hoses.
  • Boss Clamps are for single use only! Once removed they are to be discarded.
  • Recommended for steam service up to 450°F (232°C).
  • 4-bolt type with 4 gripping fingers and 2 clamp sections
  • 4 Bolt Dixon Boss Clamp Bolt Tightening Sequence, Using a torque wrench, begin tightening the bolts as follows:
  • A) Back bolt (bolt with nut facing assembler that is furthest away from gripping finger) 1 full turn.
  • B) Front bolt (bolt with nut facing assembler that is closest to gripping finger) 1 full turn.
  • C) Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued.
  • D) Opposite side back bolt (bolt with nut facing assembler furthest away from gripping finger) 1 full turn.
  • E) Opposite side front bolt (bolt with nut facing assembler closest to gripping finger) 1 full turn.
  • F) Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued.
  • G) Repeat above procedure "a" through "f" until all of the bolts have reached the recommended torque.
  • H) Remove assembly from vise.
Safety notes
  • The bolts used in the Boss interlocking clamps are not standard bolts. They vary from standard bolts in their length, diameter, overall thread length and material hardness. These bolts can be retorqued, but it is not recommended that the bolts or clamps be reused, as they are designed for a single bend only. Dixon Recommends using only factory supplied replacement bolts. Replacement nuts and bolts are available, contact Dixon for more information.
  • Torque values for clamps are based on dry bolts. The use of lubricant on bolts will adversely effect clamp performance. Do not lubricate nuts and bolts. Recommended torque rating in ft. lbs.
  • Do not use with parts: GF81, GB26, WF81, B26, RGF81, RGB26, BGF81, BGB26, RWF81, RB28
  • Worn-out hose couplings can be dangerous. They should be checked regularly and replace when necessary. Each coupling user should review applications and add safety devices where indicated.
  • Note. Pressurized steam is an extremely dangerous commodity. Only hose, fittings, clamps and accessory items that have been approved for steam service should ever be used! Never use an unapproved item for steam service. Always follow the manufacturer's product recommendations for pressurized steam handling.



SKU: 2933866

Dixon h8f8-b 1" iso-b nipple 1" nptf brass 100002-8

Great price, fast delivery.

Read more

SKU: 113319


Easy and quick.

Read more

SKU: 105947


The dies work, MRO ... the retailer ... nice ... quick ... good price and delivered in days

Read more

SKU: 6053348

Dixon hose barbs

The products were as advertised and order processing and delivery was fast and efficient.

Read more

State of California Proposition 65 Product Warning

Return policy

Item must be unused.

Item must be in it's original package.