Image for Illustration purposes only. Actual product may vary

SPX Power Team 9628 VALVE PM MANUAL POST TENSIONING

Name: SPX Power Team 9628 VALVE PM MANUAL POST TENSIONING
Brand: Hydraulic Technologies
Price: 1702.48 USD
Availability: InStock
Rating: 5.0 (1 reviews)

MODEL 9628

BRAND

Hydraulic Technologies

SKU

1967401

WEIGHT

5.400 lb

UOM

each

Contact supplier for technical support on: 800 477 8326

$1,702.48 Each

Prices are subject to change

FREE SHIPPING ON ORDERS OVER $100

Select Quantity

GET A QUOTE

Returnable:No

Flow Rate

5 gpm

Port Size

3/8 in

Pressure Rating

10000 psi

Type

Manual

Single strand, double-acting stressing jacks. 4-way/3-position (tandem center) manual valve

Application – Single strand, double-acting stressing jacks with Power Wedge seater. Actuation – Lever operated, detent positioned. Operation –

With valve in center position, pump is started.

Cable is inserted into stressing tool, valve is placed in “A” position. “Pull” portion of stressing tool is pressurized to specified level for proper cable tensioning (“A” port is checked internally, can only be released by building pressure in “B” position).

Valve is placed in “B” position, which is pressure controlled and will not exceed 6, 400 psi. “Return” portion of stressing tool is pressurized and will release “A” port when pressure reaches approximately one-half the “A” port pressure. “A” port remains open as long as this pressure differential is maintained.

Pump is stopped, valve is placed in “A” position, releasing “B” port pressure.

Used on these pumps: PA17*, PA46*, PA55, PE17*, PE21*, PE30, PE46*, PE55, PE60, PE84, PE120, PE200, PE400, PG30*, PG55, PG120, PG400, PQ60 and PQ120 series. * These pumps may have reduced first flow stage characteristics due to internal valve restrictions. caution: To prevent sudden, uncontrolled descent of a load as it is being lowered, use a Load Lowering Valve (No. 9596) or Counter Balance Valve (No. 9720) in conjunction with the directional valve used in your application. important: Conversion kit 251528 must be used when mounting any of the valves on PA17 or PE17 pumps. important: When ordering any valve for a PE30 or PG30 series pump, ½” longer mounting screws are required. For valves 9504, 9584, 9610 and 9610A, order four 12001 cap screws. For valve 9582, order two 12001 and two 10856 cap screws.

Specifications

Order No.	9628
Cylinder Application *	S. A. & D. A.
Operation	Manual
Valve Type	Post Tensioning
Volt	—
Advance / Return	Special
Advance/Hold Return	No
posi-check Feature	No
posi-check Feature	5. 4

When will I be charged for my order? Ordering Do you provide credit terms? Ordering Can I get a discounted price? I am a reseller / government entity. Ordering What is the return/warranty policy? Ordering Can it be shipped today? Ordering Does “Usually ships in 24 hours” mean it’s in stock? Ordering Read full FAQ All FAQs

5.0 out of 5 · 1 review

Mro product supply

Verified · SKU 1966869

Thanks MROSUPPLY, fair prices and good stock, fast shipping and communication. Always the first stop for tooling and supplies. Read more

Return policy

Disclaimer: The return policy information shown below is merely a copy of the text as stated in IDC-USA's Annual Return Policy.

File: http://documents.mrosupply.com/file_uploads/IDCreturnpolicy.pdf

ANNUAL RETURN POLICY PURPOSE: The purpose of IDC-USA’s Annual Return Policy is to allow IDC Distributors the opportunity to return salable stock merchandise of current design that may not have adequate “turns” and replace it with faster moving product.

ACCEPTANCE: IDC Owner-Distributors shall submit a return list to IDC-USA with all pertinent information as follows:

a. Product brand name

b. Quantity

c. IDC-USA’s product identification number

d. Corresponding distributor’s P.O. number or invoice number Acceptance of return shall be subject to IDC-USA inventory levels and manufacturer’s restrictions.

AUTHORIZATION: The return shall be audited and the IDC Owner-Distributor will receive an approved return list with a Return Material Authorization (RMA) number assigned to it. RETURN DATE: Each owner-distributor shall be assigned a month during which they shall be entitled to make a single annual return.

Product Qualification: All products returned must be:

a. On the current price list

b. In good resale condition

c. In the original packaging

d. Purchased from IDC-USA within 3 years of the return

e. Stock items only; no special order items

f. Only those items which have been approved

VALUE: The IDC Owner-Distributor shall receive a credit not to exceed 5% of the owner-distributor’s prior year annual purchases from the IDC Distribution Center. Credit received shall be the actual purchase price or price in effect at the time of the return, whichever is lowest, less applicable restocking charges. Additionally, all annual returns must have a minimum return value of $100.

RESTOCKING CHARGES: There will be a 15% restocking fee unless return is offset by a noncancelable order of equal value to be placed at the time of return. All items received that are not in their original box shall be subject to an additional 15% repackaging fee.

FREIGHT: Returns will be made freight prepaid by the IDC Owner-Distributor to the IDC Distribution Center. The packing slip and all cartons must reference the RMA number. The owner-distributor will be notified of any items received that do not qualify as set forth above. Those items will not be credited and shall be scrapped unless the IDC Owner-Distributor directs otherwise and assumes any additional transportation charges.