We never sell your data to third parties
Enerpac SRS-200TB 389452 RSM200 Cylinder w/ P392 Hand Pump and case
MODEL SRS-200TB
Contact supplier for technical support on: 800-558-0530 opt.2
Call for Pricing - 888-671-2883
Returnable: Yes
Brand
Enerpac
Model
SCL-502H
Brand
Enerpac
Model
SRS-100TB
Brand
Enerpac
Model
RCH302
Brand
Enerpac
Model
RC-258
Collapsed height (in)
2.03
Cylinder capacity advance (imperial tons)
20
Max operating pressure (psi)
10,000
Set Pump type
Hand Pump
Stroke (in)
0.44
Stroke Ranges (in)
0 - 1.99
Model: SRS200TB | ECCN:EAR99 | Harmonization:8413200000
Series: SRS - TB | Product Line: Industrial Tools
Hydraulic cylinder and pump sets (Porta power) are the quick and easy way to get you equipped to take on a wide range of lifting and pushing applications.
Included in this kit is an RSM low height single-acting hydraulic cylinder (ram). The low-height cylinder design is ideal for tight spaces, and the flat sides and through mount holes make it easy to clamp onto machinery and other fixtures.
SRS kits are available for sale in 10 – 50 ton cylinder options to suit your application.
No questions match your search.
Are all Enerpac hydraulic pumps rated for 10,000 psi? This product
No, so check the rating before you connect a pump to a cylinder or tool. Most Enerpac hand pumps, such as the P392, P80 and P842, the ZU and ZE electric pumps and the Turbo II PATG, PAMG and PARG air pumps run at 10,000 psi (700 bar). Some are lower: the P25 hand pump is rated 2,500 psi, the P51 3,000 psi and the P50 5,000 psi, and the ZW electric pumps and PACG air pumps built for workholding are 5,000 psi (350 bar). Turbo II air pumps come in 700 or 350 bar versions, so check the model. Others go higher: the HPT1500 hand pump and the ZUTP1500 and ATP1500 tensioner pumps deliver 1,500 bar (21,750 psi), and the HPN2000 hand pump is rated 2,000 bar. Every hose, gauge and cylinder on the pump must be rated for its pressure.
How do I decode an Enerpac Z-Class pump number such as ZU4308MB? This product
Enerpac's ordering guide reads the number position by position. Z is the pump class, then the motor: U universal electric, E induction electric, A air. Next is the flow group (4 is 60 in3/min), then the valve type: 1 dump VE32D, 2 three-way two-position VM32, 3 three-way three-position VM33, 4 four-way three-position VM43. Two digits give the reservoir (04 to 40), then valve operation: M manual, L manual with LCD, J or P with pendant, S solenoid, D dump. The last letter is the voltage, B for 115 V. ZU4308MB is therefore a ZU4, VM33 manual valve, 8 litre reservoir, 115 V. For other voltage letters, or to choose a pump, Enerpac asks you to send the complete model number to its technical services team.
How do I match an Enerpac pump to my cylinder? This product
Start with oil volume and valve type. A cylinder's oil capacity is its effective area times its stroke, and Enerpac says the pump's usable oil capacity should be greater than the total oil capacity of all the cylinders and hoses it feeds. A P392 hand pump, for example, has 55 cubic inches of usable oil. Single-acting cylinders need a pump with a 3-way valve and one hose; double-acting cylinders need a 4-way valve and two hoses, so for double-acting tools Enerpac points you to the P842 rather than the P392. Finally, the pump, hose and cylinder must all be rated for the same pressure.
What oil should I use in an Enerpac pump, and how do I top it up? This product
Enerpac sells two oils and says not to swap them. HF oil (HF-101 in 1 gallon, HF-102 in 5 gallons) is formulated for powered pumps and is not for use in hand pumps; LX oil (LX-101) is for hand pumps and not for power pumps. XC cordless pumps take Enerpac HF oil only, and for MP multi-fluid hand pumps Enerpac's technical services team advises on other fluids. Use only Enerpac oil to protect the warranty. Add oil only with the cylinders fully retracted (extended for pull cylinders), otherwise the system will hold more oil than the reservoir can take, and fill only to the level mark on the pump. Non-vented hand pumps need some air in the reservoir to work. For hand pumps Enerpac says to drain and refill with clean oil every 12 months, more often in dirty conditions.
What do Enerpac cylinder and pump set numbers like SCR1010H mean? This product
The set number names the cylinder and the pump. SCR sets use an RC cylinder, SCH an RCH hollow cylinder, SCL an RCS low height cylinder, SCP a BRP Pullpac cylinder and SRS an RSM Flat-Jac. The digits are the cylinder model, so SCR1010H holds an RC1010 and SCH1003H an RCH1003. The suffix gives the pump: H is a hand pump (a P142, P392 or P80 depending on the full set number), FP a P392FP foot pump, TB a P392 hand pump with a carry case and gauge, and XA an XA air pump. Enerpac lists the SCR1010H and SCH1003H as a cylinder, two-speed pump, 6 ft hose, calibrated gauge and gauge adaptor.
Service
Verified · SKU 5945427Every time i need to place an ordere with MRO the service is always prompt and friendly. Read more
Brand
Jason Industrial
Model
3836V654
Brand
BLACKSTAR
Model
BLS H50BS12 1 1/4 K2S