MROSupply Has Hundreds Of Brands, Millions Of Products, Including
Image for Illustration purposes only. Actual product may vary
SKFSEAL 17038 SMALL BORE SEALS
MODEL 17038
This vendor has a minimum order quantity of 2. Order minimum ($) may be applied. Add desired QTY to cart and proceed to checkout to view minimum
Contact supplier for technical support on: 267-436-6000
$32.04 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $1
Select Quantity
Orders over $500 qualify for a Free Gift
Brand Minimum Order Quantity: 2
Typically Ships in: 3 days
Returnable:No
Auxiliary lip
Yes
Design
CRWA1
Housing bore diameter
79.375 mm, 3.125 in
Maximum operating temperature
100.0 °C, 212.0 °F
Maximum operating temperature (°F)
100.0 °C, 212.0
Minimum operating temperature
-40.0 °C, -40.0 °F
Minimum operating temperature (°F)
-40.0 °C, -40.0
Permissible circumferential speed
7.21 m/s
Rotational speed
3240.0 r/min
Seal width
9.53 mm, 0.375 in
Sealing lip material
Nitrile rubber (NBR)
Shaft diameter
42.875 mm, 1.688 in
Type of outside diameter
Metal-cased with sealant coating on the outside diameter
Unit system
Inch
Radial shaft seal with metal case, SKF Wave lip and auxiliary, contacting lip, for oil or grease
Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. CRWA1 seals are designed with a metal case, an SKF WAVE lip made of elastomer with higher pumping rate to reduce heat generation, a garter spring to optimize sealing against the shaft, and a dust lip to improve contamination exclusion. Most of the seals feature the SKF Bore Tite coating on the outside diameter that helps fill small imperfections in the housing bore.
- For oil or grease
- With garter spring
- WAVE lip creates higher pumping rate
- WAVE lip has less friction between shaft and lip
- WAVE lip has a lower temperature at the contact point
SKU: 1898441
Mro supply - seals
I use a lot of the SKF6119 seals for chainsaw repairs and MRO always has the best prices and fast shipping.
Read moreSKU: 1898386
Small diameter seals
I use a lot of small diameter inch dimension seals for the repair of older chainsaws. MRO is a great resource for many seals with very competitive prices and free shipping for larger orders. I will continue to use MRO whenever I can.
Read moreSKU: 300488
Works good great delivery time
The seals works as they should. Delivery time was good
Read moreWhen you get to checkout, you’ll be able to select a free gift! Depending on the cart value, you’ll be shown relevant gifts your order qualifies for.
$500
MRO Hat
MRO Golf Balls
MRO Hi-Vis Vests
MRO Mug
$750
32oz Water Bottle
Throw Blanket
30 piece Hex Set
Telescopic Pick Up
$1,250
Golf Cooler
11-in-1 Screw Driver Set
Gorilla Grip Knee Pad
John Deere Oilskin Hat
$2,500
Igloo 1/2 Gallon Jug
Rechargable Headlamp
Larix Trucker Hat
$5,000
Igloo 10 Gallon Cooler
Igloo Party Bucket Cooler
Klein Tools Speaker
Klein Tools 8-in-1
$7,500
GX-6F Pro Golf Range Finder
Bushnell Outdoorsman Speaker
Jaeger 24px Ratcheting Wrench Set
Aspen Beverage Bucket
SKU: 1898441
Mro supply - seals
I use a lot of the SKF6119 seals for chainsaw repairs and MRO always has the best prices and fast shipping.
Read moreSKU: 1898386
Small diameter seals
I use a lot of small diameter inch dimension seals for the repair of older chainsaws. MRO is a great resource for many seals with very competitive prices and free shipping for larger orders. I will continue to use MRO whenever I can.
Read moreSKU: 300488
Works good great delivery time
The seals works as they should. Delivery time was good
Read moreDisclaimer: The return policy information shown below is merely an excerpt from SKF's General Conditions of Sale.
RETURN OF GOODS FOR CREDIT
Goods will not be accepted for return without prior written approval from SKF. The return freight must be prepaid by the Buyer. Unless return of Goods is due to Supplier error, Goods returned will be subject to a credit service fee of $25.00 or 15% of the credit value, whichever is greater. An additional service fee may apply is further inspection is required at the discretion of SKF