We never sell your data to third parties
$89.03 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $100
Select Quantity
Returnable:No
Brand
TB Woods
Model
9J
Brand
AMI Bearings
Model
UGCJO315-47
Component
Sleeve
Component WR2 (lbs ft2)
0.1180
Component WR²
0.118
Coupling size
10
Coupling Size or Series
10
Coupling Type
Elastomeric Coupling
Dimension (in) (D)
7 1/16
Dimension (in) (W)
3-7/16
Distance Between Shaft Ends
1.625 Inch
41.275 Millimeter
Horsepower Rating at 100 RPM
5.9
Horsepower rating at 1150 RPM
68
Horsepower rating at 1200 RPM
71
Horsepower rating at 1750 RPM
16
Horsepower rating at 1800 RPM
17
Horsepower rating at 300 RPM
18
Horsepower rating at 3450 RPM
204
Horsepower rating at 3600 RPM
213
Horsepower rating at 50 RPM
3
Horsepower rating at 690 RPM
41
Horsepower rating at 870 RPM
52
Insert design
One-Piece Solid
KW rating at 100 RPM
4.4
KW rating at 1450 RPM
64
KW rating at 3000 RPM
133
KW rating at 970 RPM
43
Material
EPDM
Material type
EPDM
Max angular gap misalignment
0.128 in
Max angular misalignment
1°
Max compatible bore size
3.375
Max parallel misalignment
10
Max RPM
3600
Max speed
3600
Maximum angular gap misalignment (in)
0.128
Maximum parallel misalignment (in)
0.025
Maximum Speed RPM
3600
Min compatible bore size
0.4375
Operating temperature
-34°C to +135°C
Outside diameter
7.0625
Outside Diameter
7.063 Inch
179.4 Millimeter
Power rating at 100 RPM
4.4 kW
Screw type
Sleeve, One-Piece, No Split
Sleeve width
3.4375
Stiffness
1241
Stiffness (in lbs rad)
10980
Temperature rating
-30°F to 275°F
Temperature rating (F)
+275ºF to -30ºF
Torque
2875In-Lbs
Torque rate
422
Torque rating (in lbs)
2875
Torsional stiffness
10980
Width
3.438 Inch
87.325 Millimeter
Shaft Couplings and Collars The TB Woods 10J E EPDM Sure-Flex Sleeve is a premier solution designed for optimal performance in various industrial applications. This elastomeric coupling element is specifically engineered to accommodate misalignment and absorb shock loads, ensuring smooth and reliable operation within power transmission systems.
Key Features
| Material Composition | Constructed from high-quality EPDM (Ethylene Propylene Diene Monomer) rubber, providing excellent resistance to heat, ozone, and aging for extended service life. |
|---|---|
| Design Flexibility | The Sure-Flex design allows for angular, parallel, and axial misalignment, accommodating varying operational conditions without compromising performance. |
| Ease of Installation | Lightweight and user-friendly, the sleeve can be easily installed or replaced, minimizing downtime in maintenance operations. |
| Versatile Compatibility | Engineered to fit with various TB Woods coupling hubs, making it adaptable to a wide range of applications within different industries. |
| Performance Characteristics | Capable of handling significant torque loads, ensuring efficient power transmission and reducing mechanical stress on components. |
Applications
| Industrial Machinery | Ideal for use in conveyors, pumps, and fans across the food and beverage, energy, and material handling industries. |
|---|---|
| Power Transmission Systems | Suitable for applications requiring robust coupling solutions that demand flexibility and durability. |
| Heavy-Duty Operations | Designed to withstand challenging operational environments, making it perfect for high-performance machinery. |
Benefits
| Enhanced Reliability | The EPDM material offers superior durability and resistance to environmental factors, reducing the frequency of replacements and maintenance. |
|---|---|
| Improved Efficiency | Efficiently absorbs shocks and vibrations, leading to smoother operation and extended lifespan of connected components. |
| Cost-Effectiveness | The combination of durability and easy installation translates into lower overall lifecycle costs, making it a smart investment for any industrial operation. |
No questions match your search.
Which Sure-Flex Plus sleeve material should I choose: EPDM, Neoprene or Hytrel? This product
EPDM is the general purpose sleeve, rated -30°F to +275°F. Neoprene is the oil resistant, non-flame option, rated 0°F to +200°F. Both allow 1 degree of angular misalignment and wind up about 21 degrees at rated torque, which helps absorb shock. Hytrel is designed for high torque, with three times the relative rating of EPDM or Neoprene (3X against 1X) and a range of -65°F to +250°F. In exchange it winds up only about 7 degrees and allows 1/4 degree of angular misalignment. TB Woods says EPDM suits about 80 percent of applications: confirm the temperature with the end user, and follow the pump or compressor maker's specification where there is one.
How do I read Sure-Flex Plus part numbers like 8J, 9JS, 12, 9HS and 8SCH178? This product
Sleeve numbers give the coupling size, then the type. J is a one-piece EPDM sleeve (8J is an 8JE) and JS is one-piece split EPDM (9JS is a 9JES). A size alone is a two-piece EPDM sleeve with a wire ring (12 is a 12E). JN and JNS are the Neoprene one-piece versions, N is two-piece Neoprene, H is solid Hytrel and HS is two-piece Hytrel. A bore after the type means a flange or hub: 6S138 is a size 6 Type S flange with a 1-3/8" bore, and 8SCH178 a size 8 SC hub with 1-7/8". SCHS marks a short hub and MPB a plain bore. Numbers such as 663150 or 73300026 do not decode this way.
Can I replace an EPDM or Neoprene sleeve with Hytrel in my existing Sure-Flex coupling? This product
Not as a direct swap. TB Woods states that rubber (EPDM or Neoprene) and Hytrel sleeves have different ratings and must not be used interchangeably, or the sleeve will fail prematurely. H and HS sleeves fit only Type S, C and SC flanges, never Type J or B. H runs in sizes 6 to 12 and HS in sizes 6 to 14. Alignment limits are also tighter: a size 8 rubber sleeve allows 0.020" parallel and 0.094" angular, against 0.015" and 0.025" for Hytrel. Going to Hytrel means reselecting the coupling, not just the sleeve.
Will new Sure-Flex Plus sleeves fit my existing Sure-Flex flanges? This product
Yes. TB Woods describes the Sure-Flex Plus sleeve as fully compatible with the industry standard design it created over 50 years ago, and says it retrofits to existing flanges, so you do not need to replace the whole coupling. Keep the same size and check the type against your flange: J, JS, JN, JNS, E and N sleeves fit any flange within a given size, H and HS only Type S, C or SC. A worn sleeve can be sized by its outside diameter and width: a size 8 is 5-1/16" OD by 2-1/2" wide. The 30% torque increase applies to EPDM and Neoprene.
How do SC spacer hubs work on a Sure-Flex Plus coupling, and what is the difference between SCH and SCHS hubs? This product
On SC spacer couplings each side is a flange bolted to a separate hub (4JSC has an integral hub), with the cap screws furnished with the hub. The flange number sets the spacing: 9SC50 is for 5" between shafts. SCH is the standard hub, bored up to 3-7/8" on size 14. SCHS is a short hub with a smaller bore range, offered in sizes 6 to 13, and using one changes the assembled length and weight. Some flanges take a larger hub for bigger shafts: 9SC50-11 is a size 9 flange that takes an 11SCH or 11SCHS. Order flanges, hubs and sleeve separately.
Tb woods
Verified · SKU 337131Excelent recomiendo 100% Read more
Sales
Verified · SKU 337299I have all good experiences with your staff. Thank you for the support. Read more
Great service!
Verified · SKU 702627It was all sent perfectly and on time Read more
Sleeve
Verified · SKU 336870Thanks for quick service and delivery was not long! Read more
Brand
Dixon
Model
400-LH-BR
Brand
Boston Gear
Model
HLK101Y
Brand
Dixon
Model
G100-A-AL
Brand
Dixon
Model
G500-DP-AL
Brand
Boston Gear
Model
HLSK103Y
Brand
Dixon
Model
G150-B-AL
Brand
Dixon
Model
G125-D-BR
Brand
Martin Sprocket
Model
M2020
Disclaimer: The return policy information shown below is merely a copy of the text as stated in TB Wood's Terms and Conditions.
File: http://documents.mrosupply.com/file_uploads/TB%20Woods%20Terms%20and%20Conditions.html
3. Claims for refunds or replacements must be made to the factory. Products may be returned only after written approval and a returned goods authorization number has been received from Customer Service or Application Engineering. Return shipments must be prepaid (Refer to Returned Goods Policy). Final decision about refund or replacement rests solely with TB Wood's Incorporated.
--
Disclaimer: The return policy featured below is for distributors only. Also, it is merely a copy of the text from TB Wood's Distributor Policy and Procedures.
File: http://documents.mrosupply.com/file_uploads/TB%20Woods%20Distributor%20Policies%20and%20Procedures.pdf
Returned Goods
The policy for returning products for defects in workmanship or materials is covered under the “Product Reliability” section.
Distributors and, occasionally, OEMs may want to return products that are overstocked or slow moving. Prior approval and a returned goods authorization number must be obtained from Customer Service or Application Engineering. This number must be referenced on the returned goods shipment. It allows us to identify the contents of the shipment, the Distributor who originated it and the reason for return. Freight must be prepaid.
Products returned for reasons other than factory authorized stock adjustments must have approval from Customer Service or Application Engineering and a returned goods authorization number. They must be sent by prepaid freight and will be subject to a 15% restocking charge. There will be additional charges as necessary for re-boxing and refurbishing. Returned goods must have been manufactured and/or sold by TB Wood’s Incorporated and must be in salable condition. They will be inspected at the factory and if reconditioning is necessary it will be charged to the Distributor. We reserve the right to reject unsalable products.
No products will be accepted for return or exchange if they are obsolete.