We never sell your data to third parties
Fenner Industrial Motion B122300 B-LOC B112 3 in
Climax Metal C405E-300 — preferred replacement
Direct drop-in replacement — MROSupply.com preferred brand for this item.
SEE Climax Metal DROP-IN REPLACEMENTMODEL B122300
Contact supplier for technical support on: 800 243 3374
$336.72 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $100
Select Quantity
Returnable: See conditions
Brand
Martin Sprocket
Model
100B23
Brand
TB Woods
Model
TL2012112
Brand
Climax Metal
Model
C405M-65X95
Axial Movement
No
Bore tolerance
4.727
Compliancy
RoHS
Component Bore Diameter
4.724"
Hub Contact Pressure
20887 psi
Hub Pressure
20887
Installation torque
60 ft lb
Internal/ External
Internal
Material
Steel
O.D.
4.724 in
Overall Length
3.15 in
Releasing/ Locking
Locking
Screw size
M10 x 60
Self-Centering
Yes
Series
B112
Shaft diameter
3 in
Shaft Tolerance
2.997
Taper
Double
Thrust
82017
Torque Transmission
10252
Transmissible Thrust
82017 lb
Transmissible Torque
10252 ft-lb
Type
Double Taper Heavy Duty
The B-LOC B112 Series 3” Keyless Bushing provides a high capacity, zero-backlash shaft to hub connection for shafts measuring 3” in diameter by means of a mechanical interference fit and also transmits up to a maximum of 10252 ft lbs torque.
Best Suited For:
Applications that require a recessed installation of the bushing with no axial movement of the mounted component relative to the shaft during tightening.
B-LOC B112 Series 3” Keyless Bushings provide a zero-backlash frictional connection that will never wear or pound out and can accommodate a high torque, thrust, bending, and/or radial loads. Their wide, double taper design enhances torque transmission and bending moment capacity while maintaining exceptional concentricity with thru-bored hubs. There is no axial movement during installation. The B-LOC B112 Series eliminates the need to hold the shaft or lock machine while applying installation torque, making for fast and easy component repositioning. Since the B-LOC B112 Series Keyless Bushings do not have a flange, the external diameter along the unit’s entire length is the same, therefore allowing the unit to be completely inserted into the component bore for flushed or recessed mounting. This series is also self-centering and RoHS compliant.Wide, double taper design for enhanced torque transmission and bending moment capacity. Exceptional concentricity with thru-bored hubs. No axial movement during installation. Self-centering. Eliminates need to hold shaft or lock machine while applying installation torque. Recessed installation without the need for a counter bore. RoHS compliant
Features of Fenner Keyless Bushings:
Ability to transmit higher torques. True zero-backlash. Less equipment downtime. Ability to mount over existing keyways. Complete axial and radial adjustability. Simple installation, adjustment and removalAll Fenner keyless locking devices operate using the simple wedge principle. An axial force is applied- by either a hex nut (Trantorque) or a series of annular screws (B-LOC)- to engage circular steel rings with mating tapers. The resulting wedge action creates a radial force on the tapered rings, one of which contracts to squeeze the shaft while the other expands and presses into the component bore.
No questions match your search.
Should I use a Trantorque, a B-LOC bushing, a shrink disc or a compression hub? This product
Fenner splits these into internal and external devices. Trantorque and B-LOC bushings are internal, fitting between shaft and bore. Trantorque uses a single hex nut and reaches 3 in (75 mm) shafts; B-LOC uses several screws and approaches 24 in (600 mm). Fenner's technical team usually recommends Trantorque up to 1-1/2 in and B-LOC above that. Shrink discs and compression hubs are external. Shrink discs suit standard coupling hubs, flanges and hollow-shaft gearbox outputs, while compression hubs suit narrow components such as plate sprockets. For a small OD to ID ratio consider B800 or Trantorque OE; for very high torque, double taper B112 or B115.
What shaft and bore finish and tolerance do Fenner keyless devices need? This product
For keyless bushings Fenner recommends 32 to 125 micro-inch (0.8 to 3.2 micrometer) RMS on shaft and hub bore; compression hubs use the same range on the shaft. Turned, ground and polished stock is too smooth and can cause failure, so roughen it lengthwise with a file or emery paper. Tolerance varies by series: plus or minus 0.003 in on Trantorque GT and OE, 0.0015 in on Mini and 0.001 in on B-LOC B109, while B103 shafts are +0/-0.002 in on bores up to 4.724 in. Shrink discs instead set a maximum clearance between shaft and hub bore, from 0.025 mm on small shafts.
Do I oil or degrease before installing a Fenner keyless device? This product
It depends on the family. Trantorque: install as received, add no lubricant, and clean shaft and bore to bare metal with a non-petroleum solvent such as isopropyl alcohol. B-LOC bushings and compression hubs: these come lightly oiled, and the screws, tapers, shaft and bore should be clean and lightly oiled with no molybdenum disulfide. Shrink discs: these come with molybdenum disulfide on the tapers and screws; oil the hub OD lightly but clean all lubricant from the shaft and hub bore, because it greatly reduces torque capacity. On every family, do not use anaerobic adhesives such as Loctite or Permatex.
How do I tighten a Trantorque or B-LOC, and will the hub move along the shaft? This product
Trantorque: hand tighten the single nut, then use a torque wrench to the listed torque, for example 125 ft-lb on a 1 in GT. Over-tightening can damage the unit. At full torque GT and OE travel about 0.075 in along the shaft, Mini about 0.045 in and NT not at all. B-LOC devices: set the wrench about 5 percent above the listed torque, tighten screws in quarter turns over several passes, add one or two passes once quarter turns stop, then reset to listed torque and check that no screw turns. B103 moves about 0.032 in; B106, B112, B115 and B400 do not. Never tighten shrink disc screws before fitting the shaft.
How do I read Fenner keyless part numbers? This product
Fenner's Metals catalog lists part numbers in size tables and prints a key only for compression hubs, where BCH502100-025 is base BCH502100 (BCH50, 1 in shaft) plus 25 mm screws. Elsewhere, check your number against the table. B-LOC numbers usually show series, unit and size: B122400 is a B112 for 4 in, B122615 for 6-15/16 in, and B401050 a B400 for 50 mm. Fenner says the third digit on every B-LOC number gives the unit, 1 for metric and 2 for inch. B800 numbers vary, such as T8012 (12 mm) and T82206 (2-3/8 in). Shrink disc B0301 is size 30-10, in SD10 standard duty. TTQM2235 is a Trantorque OE for a 22 mm shaft and 35 mm OD; EN, DC and SS mean nickel plated, chrome coated and stainless, and UP on a Trantorque GT means un-plated, shipped lightly greased.
Cutting and purchasing manager
Verified · SKU 154896The only problem I had they did not tell me it was shipping. Read more
Great value
Verified · SKU 154879Same product I got from other vendors without the price gouging. Great site. Read more
Round belts
Verified · SKU 154986These belt work exceptionally well for sewing machine applications. Very easy to change and are easily modified to fit any length. Excellent durability when it comes to industrial use sewing machines. We typically get several months(4-7) of use before replacement/modification is required. Read more
One of my best suppliers
Verified · SKU 154593Great and fast service, product quality is so good! Read more
Brand
Martin Sprocket
Model
2 B 136 SK
Brand
Marathon Electric
Model
182TTDBD6014
Brand
Martin Sprocket
Model
TS832
Brand
Baldor
Model
EM4110T-8
Brand
JW Winco
Model
903-25-M12-74-ST
Brand
MROSupply Fasteners
Model
FSTPCK-702066
Brand
Baldor
Model
EJMM4109T
Item must be unused.
Item must be in it's original package.
Restocking, shipping and handling fees may apply to any return with this manufacturer.
For more information please consult https://www.mrosupply.com/page/returnwarranty-policy/