Image for Illustration purposes only. Actual product may vary
SFWC718-400-B5-G Cast Iron Worm Gearbox
- Ratio: 400:1 Double Reduction
- Center Distance: 1.8"
- Input: 56C Flange
- Output Bore/Shaft Diameter: 0.875"
- Output: Left Side Solid Output Shaft
MODEL SFWC718-400-B5-G
Contact supplier for technical support on: 888-999-9860
$2,154.59 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $1
Select Quantity
Free Gift with this product
Typically Ships in: 1 day
Returnable: See conditions
Bore/Shaft Diameter
0.875"
Center Distance
1.8"
Input Size
56C
Input Type
Flange
Output Type
Solid Output Shaft
Reduction
Double
Shaft Projection
Left Side
Product Features
- The 700 Series' large oil reservoir provides efficient heat dissipation and lubrication for longer operating life.
- Its multi-position mounting flexibility allows for installation in virtually any position.
- Housings are straddle-milled, top and bottom, for precise alignment of horizontal and vertical bases.
- Internal baffles assure positive, leak-free venting.
- The 700 Series' rugged housing, fabricated of fine-grained, gear-quality cast iron, provides maximum strength for maximum durability, as well as greater precision during worm and gear alignment.
- Boston Gear's 700 Series high-strength bronze worm gear is straddle mounted between heavy-duty tapered roller bearings to increase thrust and overhung load capacities, sizes 713-760.
- 700 Series' high-strength steel output shaft assures capacity for high torque and overhung loads.
- Pipe plugs allow easy fill, level, and drain in any mounting position.
- The 700 Series' super-finished oil-seal diameters on both input and output shafts extend seal life.
Specifications
- 11 basic single reduction sizes
- 8 basic double reduction sizes
- 1/6 - 25 HP
- 5:1 - 100:1 ratios single reduction
- 100:1 - 3600:1 ratios double reduction
- Non-flanged, NEMA C-face quill, and coupled input styles
- Projecting and hollow output shafts
- Projecting diameters from 1/2" to 2-1/4"
- Hollow output bore diameters from 5/8" to 3-7/16" (with over 20 bore sizes in stock)
SKU: 34774
Quality
very high quality. using these gears in a model 9 cylinder radial engine with a 1" bore. about 8 h.p. , for oil pump a scavenge pump timing gears and distributor . very good quality gears.
Read moreSKU: 38771
Gear box oil
This has been very hard to find. It’s the oil spec’ed for my 1950s Rockwell wedge bed planer gear box. I haven’t found it anyplace else.
Read moreSKU: 6132994
Speed reducer purchase
The purchase was easy it did take two purchase until we got the correct part I guess it was a fault on both parts as we were looking at the wrong part number, but overall the purchase was good part fit perfectly. Thanks for your support.
Read moreWhen you get to checkout, you’ll be able to select a free gift! Depending on the cart value, you’ll be shown relevant gifts your order qualifies for.
$500
MRO Hat
MRO Golf Balls
MRO Hi-Vis Vests
MRO Mug
$750
32oz Water Bottle
Throw Blanket
30 piece Hex Set
Telescopic Pick Up
$1,250
Golf Cooler
11-in-1 Screw Driver Set
Gorilla Grip Knee Pad
John Deere Oilskin Hat
$2,500
Igloo 1/2 Gallon Jug
Rechargable Headlamp
Larix Trucker Hat
$5,000
Igloo 10 Gallon Cooler
Igloo Party Bucket Cooler
Klein Tools Speaker
Klein Tools 8-in-1
$7,500
GX-6F Pro Golf Range Finder
Bushnell Outdoorsman Speaker
Jaeger 24px Ratcheting Wrench Set
Aspen Beverage Bucket
SKU: 34774
Quality
very high quality. using these gears in a model 9 cylinder radial engine with a 1" bore. about 8 h.p. , for oil pump a scavenge pump timing gears and distributor . very good quality gears.
Read moreSKU: 38771
Gear box oil
This has been very hard to find. It’s the oil spec’ed for my 1950s Rockwell wedge bed planer gear box. I haven’t found it anyplace else.
Read moreSKU: 6132994
Speed reducer purchase
The purchase was easy it did take two purchase until we got the correct part I guess it was a fault on both parts as we were looking at the wrong part number, but overall the purchase was good part fit perfectly. Thanks for your support.
Read moreItem must be unused.
Item must be in it's original package.
25% Restocking, shipping and handling fees may apply to any return with this manufacturer.
For more information please consult https://www.mrosupply.com/page/returnwarranty-policy/