Stop searching, install MROSupply Smart Check and see our price instantly wherever you browse.

Download Now

Add products to your shopping cart
Know When You’re Overpaying
The MROSupply Chrome Extension instantly alerts you when the part you’re viewing is available for less at MROSupply.
Download Now
We never track your browsing or search history
We never sell your data to third parties
T402315

Image for Illustration purposes only. Actual product may vary

View in markdown

Fenner Industrial Motion T402315 B-LOC B400 3-15/16 in

C200E-393
PREFERRED BRAND

Climax Metal C200E-393 — preferred replacement

Direct drop-in replacement — MROSupply.com preferred brand for this item.

SEE Climax Metal DROP-IN REPLACEMENT

MODEL T402315

SKU

818167

WEIGHT

4.700 lb

UOM

each

Contact supplier for technical support on: 800 243 3374

$137.78 Each

Prices are subject to change

FREE SHIPPING ON ORDERS OVER $100

Select Quantity

GET A QUOTE

Returnable: See conditions

Suggested Items
T402315

#818167

Brand

Fenner Industrial Motion

Model

T402315

$137.78 Each
Free shipping
T602315

#818209

Brand

Fenner Industrial Motion

Model

T602315

$135.46 Each
Free shipping
T302315

#818135

Brand

Fenner Industrial Motion

Model

T302315

$192.74 Each
Free shipping
T122315

#818061

Brand

Fenner Industrial Motion

Model

T122315

$499.27 Each
Free shipping

Axial Movement

No

Bore Diameter

3-15/16 in

Bore tolerance

5.713

Component Bore Diameter

5.709"

Hub Contact Pressure

26204 psi

Hub Pressure

26204

Installation torque

91 ft lb

Internal/ External

Internal

Material

Steel

O.D.

5.709 in

Overall Length

1.772 in

Releasing/ Locking

Releasing

Screw size

M12 x 30

Self-Centering

No

Series

B400

Shaft diameter

3 15/16 in

Shaft Tolerance

3.9335

Taper

Double

Thrust

57726

Torque Transmission

9471

Transmissible Thrust

57726 lb

Transmissible Torque

9471 ft-lb

Type

Double Taper

The B-LOC B400 Series 3-15/16” Keyless Bushing provides a high capacity, zero-backlash shaft to hub connection for shafts measuring 3-15/16” in diameter by means of a mechanical interference fit and transmits up to a maximum of 9471 ft lbs of torque.

Best Suited For:

Applications that require a recessed installation of the bushing with no axial movement of the mounted component relative to the shaft during tightening.

B-LOC B400 Series 3-15/16” Keyless Bushings provide a zero-backlash frictional connection that will never wear or pound out and can accommodate high-torque, thrust, bending, and/or radial loads. Their self-releasing double taper design permits simple adjustment and removal and there is no axial movement during installation. Since the B-LOC B400 Series Keyless Bushings do not have a flange, the external diameter along the unit’s entire length is the same, therefore allowing the unit to be completely inserted into the component bore for flushed or recessed mounting.Self-releasing double taper design permits simple adjustment and removal. No axial movement during installation. Recessed installation without the need for a counterboreNote: This product is not self-centering but Fenner offers pilot bushings that provide pre-centering when required. The pilot bushings are supplied in sets of three (3) bushings and three (3) longer screws (replace plated locking screws).
Features of Fenner Keyless Bushings:

Ability to transmit higher torques. True zero-backlash. Less equipment downtime. Ability to mount over existing keyways. Complete axial and radial adjustability. Simple installation, adjustment and removalAll Fenner keyless locking devices operate using the simple wedge principle. An axial force is applied- by either a hex nut (Trantorque) or a series of annular screws (B-LOC)- to engage circular steel rings with mating tapers. The resulting wedge action creates a radial force on the tapered rings, one of which contracts to squeeze the shaft while the other expands and presses into the component bore.

Should I use a Trantorque, a B-LOC bushing, a shrink disc or a compression hub? This product

Fenner splits these into internal and external devices. Trantorque and B-LOC bushings are internal, fitting between shaft and bore. Trantorque uses a single hex nut and reaches 3 in (75 mm) shafts; B-LOC uses several screws and approaches 24 in (600 mm). Fenner's technical team usually recommends Trantorque up to 1-1/2 in and B-LOC above that. Shrink discs and compression hubs are external. Shrink discs suit standard coupling hubs, flanges and hollow-shaft gearbox outputs, while compression hubs suit narrow components such as plate sprockets. For a small OD to ID ratio consider B800 or Trantorque OE; for very high torque, double taper B112 or B115.

What shaft and bore finish and tolerance do Fenner keyless devices need? This product

For keyless bushings Fenner recommends 32 to 125 micro-inch (0.8 to 3.2 micrometer) RMS on shaft and hub bore; compression hubs use the same range on the shaft. Turned, ground and polished stock is too smooth and can cause failure, so roughen it lengthwise with a file or emery paper. Tolerance varies by series: plus or minus 0.003 in on Trantorque GT and OE, 0.0015 in on Mini and 0.001 in on B-LOC B109, while B103 shafts are +0/-0.002 in on bores up to 4.724 in. Shrink discs instead set a maximum clearance between shaft and hub bore, from 0.025 mm on small shafts.

Do I oil or degrease before installing a Fenner keyless device? This product

It depends on the family. Trantorque: install as received, add no lubricant, and clean shaft and bore to bare metal with a non-petroleum solvent such as isopropyl alcohol. B-LOC bushings and compression hubs: these come lightly oiled, and the screws, tapers, shaft and bore should be clean and lightly oiled with no molybdenum disulfide. Shrink discs: these come with molybdenum disulfide on the tapers and screws; oil the hub OD lightly but clean all lubricant from the shaft and hub bore, because it greatly reduces torque capacity. On every family, do not use anaerobic adhesives such as Loctite or Permatex.

How do I tighten a Trantorque or B-LOC, and will the hub move along the shaft? This product

Trantorque: hand tighten the single nut, then use a torque wrench to the listed torque, for example 125 ft-lb on a 1 in GT. Over-tightening can damage the unit. At full torque GT and OE travel about 0.075 in along the shaft, Mini about 0.045 in and NT not at all. B-LOC devices: set the wrench about 5 percent above the listed torque, tighten screws in quarter turns over several passes, add one or two passes once quarter turns stop, then reset to listed torque and check that no screw turns. B103 moves about 0.032 in; B106, B112, B115 and B400 do not. Never tighten shrink disc screws before fitting the shaft.

How do I read Fenner keyless part numbers? This product

Fenner's Metals catalog lists part numbers in size tables and prints a key only for compression hubs, where BCH502100-025 is base BCH502100 (BCH50, 1 in shaft) plus 25 mm screws. Elsewhere, check your number against the table. B-LOC numbers usually show series, unit and size: B122400 is a B112 for 4 in, B122615 for 6-15/16 in, and B401050 a B400 for 50 mm. Fenner says the third digit on every B-LOC number gives the unit, 1 for metric and 2 for inch. B800 numbers vary, such as T8012 (12 mm) and T82206 (2-3/8 in). Shrink disc B0301 is size 30-10, in SD10 standard duty. TTQM2235 is a Trantorque OE for a 22 mm shaft and 35 mm OD; EN, DC and SS mean nickel plated, chrome coated and stainless, and UP on a Trantorque GT means un-plated, shipped lightly greased.

When will I be charged for my order? Ordering Do you provide credit terms? Ordering Can I get a discounted price? I am a reseller / government entity. Ordering What is the return/warranty policy? Ordering Can it be shipped today? Ordering Does “Usually ships in 24 hours” mean it’s in stock? Ordering Read full FAQ All FAQs
5.0 out of 5 · 4 reviews

Cutting and purchasing manager

Verified · SKU 154896

The only problem I had they did not tell me it was shipping. Read more

Great value

Verified · SKU 154879

Same product I got from other vendors without the price gouging. Great site. Read more

Round belts

Verified · SKU 154986

These belt work exceptionally well for sewing machine applications. Very easy to change and are easily modified to fit any length. Excellent durability when it comes to industrial use sewing machines. We typically get several months(4-7) of use before replacement/modification is required. Read more

One of my best suppliers

Verified · SKU 154593

Great and fast service, product quality is so good! Read more

Recently Viewed
CMAC 8600-2

#2067439

Brand

SKF Bearing

Model

CMAC 8600-2

$157.71 Each
Free shipping
M30

#5929591

Brand

Bando

Model

M30

$5.08 Each
Free Shipping orders over $100
VA-65

#2395748

Brand

Harwal

Model

VA-65

$4.84 Each
Free Shipping orders over $100

Return policy

Item must be unused.

Item must be in it's original package.

Restocking, shipping and handling fees may apply to any return with this manufacturer.

For more information please consult https://www.mrosupply.com/page/returnwarranty-policy/