Categories

Subtotal

View cart
Add products to your shopping cart
#1967520

Image for Illustration purposes only. Actual product may vary

SPX 1158 PULLER-PILOT BEARING

Add to cart to see a price so low we can't advertise it!

NEW

  • Typically ships in: 1 day
  • Weight: 12.2 lb
  • Free shipping on orders over $20
  • Payment methods:
  • Returnable:No
  • Unit of Measure: EA

Select Quantity

Additional Description

Practical for pulling motor, generator, and magneto bearings. Also good for removing small-bore bushings, bearings and oil seeds.

Slide hammer puller set This very handy set is ideal for those close-quarter, inside pulling jobs. Very practical for pulling motor, generator, and magneto bearings. Also good for removing small-bore bushings, bearings, and oil seals.

Slide hammer puller set This useful set contains a reversible-jaw slide hammer puller with a 2.5 lb. sliding hammer plus an assortment of special jaws (3 of each size) and adapters. In this set, you get all the versatility you demand of a slide hammer puller.

Sliding hammers only -

Bearing cup remover The 7136 is perfect for pulling internal bearing cups, seals, bushings, etc. Jaw spread - 15/16" to 3 1/4", reach to 3 1/2". Use with any slide hammer having 5/8"-18 thread (Power Team 1155, 1156 or 927 Push-Puller).

Pilot bearing pullers These very versatile pullers are built especially for inside pulling jobs, and particularly for removing flywheel pilot bearings on machines and construction vehicles. Also very practical for pulling motor, generator and magneto bearings.

Special slide hammer puller Ideal for pulling jobs in very close quarters, as in removal of small-bore bushings, bearings, oil seals, etc. Internal pulling attachment has jaw spread of 1/2" to 1 3/8". Handle end has a 1/2"– 20 thread.

Basic slide hammer units Compatible with internal pulling attachment. Compatible with female-threaded adapters, and male-threaded adapters. 24" in length, 5/8"–18 threaded end.

Reversible-jaw slide hammer pullers Ideal for pulling gears, bearings, outer races, grease retainers, oil seals, etc. Two or three jaws may be used and positioned for “inside” or “outside” pulling jobs. Both have 5/8"– 18 threaded end so attachments and adapters may be used.

Slide hammer pullers with cup pulling attachments These combine a basic slide hammer with No. 1152 internal pulling attachment for removing oil seals, outer races, and bearing cups from blind holes.

Specifications
Order No.DescriptionWeight (lbs.)
1158Same as 1157 but with 1155 slide hammer.12.2

Return policy

Disclaimer: The return policy information shown below is merely a copy of the text as stated in IDC-USA's Annual Return Policy.

File: http://documents.mrosupply.com/file_uploads/IDCreturnpolicy.pdf

ANNUAL RETURN POLICY PURPOSE: The purpose of IDC-USA’s Annual Return Policy is to allow IDC Distributors the opportunity to return salable stock merchandise of current design that may not have adequate “turns” and replace it with faster moving product.

ACCEPTANCE: IDC Owner-Distributors shall submit a return list to IDC-USA with all pertinent information as follows:

a. Product brand name

b. Quantity

c. IDC-USA’s product identification number

d. Corresponding distributor’s P.O. number or invoice number Acceptance of return shall be subject to IDC-USA inventory levels and manufacturer’s restrictions.

AUTHORIZATION: The return shall be audited and the IDC Owner-Distributor will receive an approved return list with a Return Material Authorization (RMA) number assigned to it. RETURN DATE: Each owner-distributor shall be assigned a month during which they shall be entitled to make a single annual return.

Product Qualification: All products returned must be:

a. On the current price list

b. In good resale condition

c. In the original packaging

d. Purchased from IDC-USA within 3 years of the return

e. Stock items only; no special order items

f. Only those items which have been approved

VALUE: The IDC Owner-Distributor shall receive a credit not to exceed 5% of the owner-distributor’s prior year annual purchases from the IDC Distribution Center. Credit received shall be the actual purchase price or price in effect at the time of the return, whichever is lowest, less applicable restocking charges. Additionally, all annual returns must have a minimum return value of $100.

RESTOCKING CHARGES: There will be a 15% restocking fee unless return is offset by a noncancelable order of equal value to be placed at the time of return. All items received that are not in their original box shall be subject to an additional 15% repackaging fee.

FREIGHT: Returns will be made freight prepaid by the IDC Owner-Distributor to the IDC Distribution Center. The packing slip and all cartons must reference the RMA number. The owner-distributor will be notified of any items received that do not qualify as set forth above. Those items will not be credited and shall be scrapped unless the IDC Owner-Distributor directs otherwise and assumes any additional transportation charges.

 

Product's availability

State of California Proposition 65 Product Warning