We never sell your data to third parties
Dodge 040760 P4B522-USAF-400LER four-bolt pillow block bearing with 4" bore, tapered adapter shaft attachment, and spherical roller insert. Split cast iron housing, labyrinth seal, greasable, sensor-ready, non-expansion fixed type for heavy-duty
MODEL 040760
Contact supplier for technical support on: +1-864-284-5700
$1,889.18 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $100
Select Quantity
Typically Ships in: 1 day
Returnable: See conditions
Base to center height
4.9400 in, 125.476 mm
Bearing component
Mounted Bearing
Bearing type
Spherical roller, spherical roller
Bolt Diameter
0.7500 in
Bolt to bolt max
14.5000 in, 368.3 mm
Bolt to bolt min
12.5900 in, 319.786 mm
Bolt width
2.7500 in, 69.85 mm
Bore length
6.5900 in, 167.386 mm
Expansion capability
Non-expansion (fixed)
Greasable
Yes
Housing construction
Split
Housing type
Four-bolt pillow block
Insert material
Steel
Lubrication type
Grease
Max Speed
2000 RPM
Seal type
Labyrinth
Sensor ready
Yes
Shaft attachment
Tapered adapter
Shaft diameter
4.0000 in
Static load capacity
134000 lbf, 596061.696 N
DODGE UNIFIED SAF and SDAF Pillow Blocks
Features/Benefits
- Cast iron, closed-end housings offer greater protection in high pressure washdown environments. Available from stock.
- Solid cast iron feet increase strength in both two and fourbolt styles.
- Large capacity oil sump lowers operating temperatures, undercut bearing seat allows full lateral travel of expansion bearing, prevents stabilizer ring from binding, makes installation easy
- Oil return slots are cast into the interior seal grooves to keep lubricants in. This allows oil in the seal grooves to return to the oil sump instead of leaking.
- Standard modifications for wet and harsh environments include nylon coating, epoxy paints and nickel plating, as well as stainless steel hardware.
- New drop-in TRIPLE-TECT Seal makes seal installation easier
- Exclusive oil-equalization passage simplifies maintenance. Pillow block can be drained completely from either side.
- Offset dowels with matched numbers on cap and base joint simplify correct assembly.
SKU: 117869
Awesome transaction
Great company to do business with. Transaction went smooth and quick!
Read moreSKU: 118299
Prompt & great service
As usual MRO Supply team are quick in shipping the ordered parts correctly without any delay.. Will shop online again confidently knowing they offer very good and prompt service!
Read moreSKU: 5005293
Dodge conveyor bushings
The right part, in stock, easy to find, quickly shipped.
Read moreHow do I choose the right type of bearing for my application?
Start with the load and how it’s applied. You need to know if you’re dealing with radial loads, axial loads, or a mix of both. Then look at speed, operating environment, and space constraints. For example, ball bearings are great for high speed and lighter loads, while roller bearings handle heavier loads but usually at lower speeds. If there’s contamination, moisture, or heat involved, you may need sealed bearings or specific materials. In most cases, the right choice comes down to matching load type, speed, and environment to the bearing design.
Face Runout/OD is the variation of the outside surface generatrix inclination with the face. This tolerance is meant to help ensure the outer ring of the bearing is close enough to a right angle with the face of the outer ring. The figures for the face runout/OD are provided for P4 and P5 grades. Note that all points on a single circle of the outside ring bore adjacent to the face are calculated based on one revolution. However, the inner ring must remain stationary. Then, the bearing is turned over and the outer side of the ring measured. Finally, the largest measurement is taken away from the smallest to get runout/OD bore tolerance.
Read More
#124150
Brand
Dodge
Model
040760
#126511
Brand
Dodge
Model
042540
#126528
Brand
Dodge
Model
042049
#132705
Brand
Dodge
Model
045943
#134010
Brand
Dodge
Model
042525
| Brand | Thomson Linear |
| Model | 512P45B3Z |
| Brand | PIP |
| Model | 4031/M |
SKU: 117869
Awesome transaction
Great company to do business with. Transaction went smooth and quick!
Read moreSKU: 118299
Prompt & great service
As usual MRO Supply team are quick in shipping the ordered parts correctly without any delay.. Will shop online again confidently knowing they offer very good and prompt service!
Read moreSKU: 5005293
Dodge conveyor bushings
The right part, in stock, easy to find, quickly shipped.
Read moreItem must be unused and undamaged, in it's orginal package. For Dodge there is typically a 10% + $30 US re-stocking fee, although it may vary from case to case. Re-packing fees may apply. Re-stocking fee applies bor both returns for credit and return for exchange.
Warranty is redeemed directly with manufacturer. If your item was damaged during usage, please let us know and we will help you get in touch with your nearest service center, they will guide you about the steps to follow to redeem the manufacturer's warranty.
For further information on our returns/warranty policy, please visit:
https://www.mrosupply.com/page/returnwarranty-policy/