We never sell your data to third parties
Boston Gear RF752-10F-B11-J 10:1 single reduction worm gear speed reducer from the 700 Series. Cast iron housing with 5.2" center distance. Coupling flange input accepts 210TC NEMA C-face motor. Right side solid output shaft with 2" diameter. Designed for general industrial power transmission applications.
MODEL RF752-10F-B11-J
Contact supplier for technical support on: 800-626-2120
$4,115.38 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $100
Select Quantity
Typically Ships in: 1 day
Returnable: See conditions
Bore/Shaft Diameter
2"
Center Distance
5.2"
Input Flange
210TC
Input Size
210TC
Input Style
3-Piece Coupled
Input Type
Flange
Output
Right
Output Type
Solid Output Shaft
Paint/Coating
Gray
Ratio
10 to 1
Reduction
Single
Shaft Projection
Right Side
Product Features
- The 700 Series' large oil reservoir provides efficient heat dissipation and lubrication for longer operating life.
- Its multi-position mounting flexibility allows for installation in virtually any position.
- Housings are straddle-milled, top and bottom, for precise alignment of horizontal and vertical bases.
- Internal baffles assure positive, leak-free venting.
- The 700 Series' rugged housing, fabricated of fine-grained, gear-quality cast iron, provides maximum strength for maximum durability, as well as greater precision during worm and gear alignment.
- Boston Gear's 700 Series high-strength bronze worm gear is straddle mounted between heavy-duty tapered roller bearings to increase thrust and overhung load capacities, sizes 713-760.
- 700 Series' high-strength steel output shaft assures capacity for high torque and overhung loads.
- Pipe plugs allow easy fill, level, and drain in any mounting position.
- The 700 Series' super-finished oil-seal diameters on both input and output shafts extend seal life.
SKU: 36216
Worm
Haven't used them yet, but they match the worm gear perfectly. They should serve the purpose for which I purchased them.
Read moreSKU: 35104
12d.p. 14t spur gear
This item was closer to exactly what I needed than I had thought possible to find in the last 75 or so years. quite affordable, too. I almost didn't look, but when I did, there it was. I had in hand in just a couple of days.
Read moreSKU: 34774
Quality
very high quality. using these gears in a model 9 cylinder radial engine with a 1" bore. about 8 h.p. , for oil pump a scavenge pump timing gears and distributor . very good quality gears.
Read moreSKU: 6132994
Speed reducer purchase
The purchase was easy it did take two purchase until we got the correct part I guess it was a fault on both parts as we were looking at the wrong part number, but overall the purchase was good part fit perfectly. Thanks for your support.
Read more
| Brand | Precision Twist Drill |
| Model | QC21G9/64 |
SKU: 36216
Worm
Haven't used them yet, but they match the worm gear perfectly. They should serve the purpose for which I purchased them.
Read moreSKU: 35104
12d.p. 14t spur gear
This item was closer to exactly what I needed than I had thought possible to find in the last 75 or so years. quite affordable, too. I almost didn't look, but when I did, there it was. I had in hand in just a couple of days.
Read moreSKU: 34774
Quality
very high quality. using these gears in a model 9 cylinder radial engine with a 1" bore. about 8 h.p. , for oil pump a scavenge pump timing gears and distributor . very good quality gears.
Read moreSKU: 6132994
Speed reducer purchase
The purchase was easy it did take two purchase until we got the correct part I guess it was a fault on both parts as we were looking at the wrong part number, but overall the purchase was good part fit perfectly. Thanks for your support.
Read moreItem must be unused.
Item must be in it's original package.
25% Restocking, shipping and handling fees may apply to any return with this manufacturer.
For more information please consult https://www.mrosupply.com/page/returnwarranty-policy/